notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.15 and 0.30mm from terminal tip. 4. coplanarity applies to the exposed pad as well as the terminals. c a seating plane d e 0.10 c a3 a a1 2x 2x 0.10 c wdfn6 1.5x1.5, 0.5p case 511bj ? 01 issue b date 06 jul 2010 scale 4:1 dim a min max millimeters 0.70 0.80 a1 0.00 0.05 a3 0.20 ref b 0.20 0.30 d e e l pin one reference 0.05 c 0.05 c a 0.10 c note 3 l2 e b b 3 6 6x 1 4 0.05 c mounting footprint* l1 1.50 bsc 1.50 bsc 0.50 bsc 0.40 0.60 --- 0.15 generic marking diagram* *this information is generic. please refer to device data sheet for actual part marking. pb ? free indicator, ?g? or microdot ? ?, may or may not be present. bottom view l 5x dimensions: millimeters 0.73 6x 0.35 5x 1.80 0.50 pitch *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. l1 detail a l alternate terminal constructions ?? l2 0.50 0.70 top view b side view note 4 recommended 0.83 x = specific device code m = date code = pb ? free package x m 1 (note: microdot may be in either location) mechanical case outline package dimensions http://onsemi.com 1 ? semiconductor components industries, llc, 2002 october, 2002 ? rev. 0 case outline number: xxx document number: status: new standard: description: 98aon50296e on semiconductor standard wdfn6, 1.5 x 1.5, 0.5 p electronic versions are uncontrolled except when accessed directly from the document repository. printed versions are uncontrolled except when stamped ?controlled copy? in red. page 1 of 2
document number: 98aon50296e page 2 of 2 issue revision date o released for production. req. by b. marquis. 13 apr 2010 a corrected marking diagram. req. by b. marquis. 30 apr 2010 b corrected marking diagram from two characters to one. req. by b. marquis. 06 jul 2010 ? semiconductor components industries, llc, 2010 july, 2010 ? rev. 01b case outline number: 511bj on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner.
|
